Coppermine Stats
Photo Albums
• Albums: 308
• Pictures: 2452 · Views: 824590 · Votes: 1316
· Comments: 86
|
Best quality brass??Discussion regarding the reloading of ammunition and tuning of loads for accuracy
Go to page Previous 1, 2, 3, 4, 5, 6, 7 Next
View previous topic :: View next topic |
|
Author |
Message |
SingleShotLover Super Member
Joined: Dec 26, 2007 Posts: 1005 Location: Illinois
|
Posted: Sun Jun 22, 2014 10:47 am Post subject: Re: Best quality brass?? |
|
Bolt face issues will not create lack of concentricity as such. Unless cartridges are loaded to such maximum dimensions that they are jammed into a chamber, the fit between bolt-face and cartridge head head is somwhat loose due to extractor issues and etc. The chamber controls alignment. If a bolt face is off-square it might create a support problem, which would probably cause accuracy issues, but not alignment. Even assuming a"perfect" chamber, a bullet that is even slightly out of perfect alignment will enter the rifling at a slight angle causing the bullet to not be centered in the bore. Granted, this is a miniscule amount, but effects down range can be dramatic.
_________________ If you can't hit it with one, you probably can't with two either!
The biggest problem with a closed mind is that it never seems to come with a closed mouth.
SSL |
|
Back to top |
|
|
Donut Slayer Super Member
Joined: Jun 27, 2007 Posts: 594 Location: Pensacola, Florida
|
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8316 Location: Fort Worth TX
|
Posted: Sun Jun 22, 2014 8:15 pm Post subject: Re: Best quality brass?? |
|
Well stated SSL. I will add two things. Every time you fire the case, it becomes concentric again as it expands out in the chamber/bore. Its the reloading process the gets it out of alignment. Size the neck down, expand it back out (if not an S-type die), and seating the bullet if not held in alignment. The case can become and issue. Over time the neck thickness will begin to vary by more than a couple thousanths (thick sections do not stretch as much as the thin parts). Once the variation exceeds 0.003, it might be worth tossing it and starting with a new case.
DSlayer, the over-work brass occurs when the case goes into the die then the expander ball enlarges it. Take your expander ball out and run a case through. Measure the neck and see how much undersized it is. Now you see how much the expander ball has to expand the neck back out. With a Redding S-Type die, you buy the bushing the will size the case neck down to what you need - the minimum required. I'd be interested if you would post your numbers. Do you know how to adjust your FL resizing die to fit your chamber? My 130gr GMX load groups best with neck-size only ($20 Lee hand loader). My 129gr LRX groups best with full-length resized.
_________________ "To anger a conservative, lie to him. To anger a liberal, tell him the truth." - Theodore Roosevelt
"The world is a dangerous place to live; not because of the people who are evil, but because of the people who don't do anything about it." - Albert Einstein |
|
Back to top |
|
|
Donut Slayer Super Member
Joined: Jun 27, 2007 Posts: 594 Location: Pensacola, Florida
|
|
Back to top |
|
|
PaulS Super Member
Joined: Feb 18, 2006 Posts: 4330 Location: South-Eastern Washington - the State
|
Posted: Sun Jun 22, 2014 9:02 pm Post subject: Re: Best quality brass?? |
|
All I can talk about is my own experience. I have been loading since 1971 but the first two years I used the Lee loaders in the box. Even with the little Lee loaders I made ammo that was sub- one inch groups at 100 yards. (this in a sporterized 03A3). Once I got my press and started into reloading I had a heck of a time getting small groups until I started neck sizing again. I started neck sizing because I got a few "J" splits (body splits that ran up and down the case) and realized that my chamber was so big (military) that I was working the brass too much sizing it. That helped but I started just partially neck sizing - size just the first 60 to 70% of the neck and leave part of it expanded so it fits the chamber better - that's when my groups dropped to 9/16" to 5/8" at 100 yards. I shoot five shot groups instead of the "normal" three shot groups just because I use five shot groups with my revolvers. I like everything "standardized" I guess. Anyway the partial neck sizing keeps the bullet better aligned with the bore than when it is resting on the bottom of the chamber - at least that's the reason I use. The case is expanded to fit the chamber and the rear of the neck is too. It just makes sense to do it that way - especially when it works so well for me. I load the same way for all my guns - bolt action and break-open. I hear stories of having to "push" the shoulder back so the cartridge will chamber but I have never had to do that and I believe that would be a sign of excessive pressure. The brass will only expand to the size of the chamber and the harder the brass gets the better spring it is - right up to the point of cracking. I've not had any problems even after loading a case 20 times and more. I don't experience heavy bolt lift and my fired cases will fall into the chamber under their own weight. I never exceed maximum listed loads and I rarely use maximum loads. Most of my loads run at 95 to 97% of maximum listed charges. I load for accuracy and the velocity takes care of itself. I don't use my chronograph until I have an accurate load worked up already. Then I use the chronograph to get the velocity so I can work out my 1" point blank range. I use ballistics software - like Point Blank - to approximate my adjustments for extended ranges but I shoot at those ranges to find out where my bullets are actually impacting at those extended ranges. The software gets you close but I have seen deviations as high as 2.5" at 300 yards.
Every rifle is different and what works for me may not be necessary or even of any value in another gun. Target chambers, by design, do the same thing that partial neck sizing does because clearances are held so much tighter. I just don't have any rifles that have target chambers - or even tight chambers.
When you do find something that works then keep doing it. Going from full length sizing to neck only sizing takes a few firings to get the case where it is an ideal fit in the chamber so try it for a while before you decide it doesn't improve anything. You may even have to adjust your loads due to the extra space in the swelled case.
Have fun with it, take your time to se what works to improve your groups and enjoy!
Paul
_________________ Paul
__________________
Speer, Lyman, Hodgdon, Sierra, and Hornady = reliable loading data
So and So's pages on the internet = NOT reliable loading data
Always check data against manuals
NEVER exceed maximum listed loads |
|
Back to top |
|
|
Donut Slayer Super Member
Joined: Jun 27, 2007 Posts: 594 Location: Pensacola, Florida
|
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8316 Location: Fort Worth TX
|
Posted: Mon Jun 23, 2014 5:34 pm Post subject: Re: Best quality brass?? |
|
DSlayer, my .308 brass would be neck-sized down 0.005" with an S-Type/Bushing die (that distance depends on the individual chamber, some more, some a thou less). With a standard expander-ball die that would be neck down 0.011" then expand back out 0.006". The numbers may be small but the relative magnitude is, IMO, significant (3x) and work-hardends the brass more. If you don't anneal your case necks, this adds up.
_________________ "To anger a conservative, lie to him. To anger a liberal, tell him the truth." - Theodore Roosevelt
"The world is a dangerous place to live; not because of the people who are evil, but because of the people who don't do anything about it." - Albert Einstein |
|
Back to top |
|
|
Donut Slayer Super Member
Joined: Jun 27, 2007 Posts: 594 Location: Pensacola, Florida
|
|
Back to top |
|
|
Vince Site Admin
Joined: May 25, 2005 Posts: 15721 Location: Brisbane AUSTRALIA
|
Posted: Mon Jun 23, 2014 11:37 pm Post subject: Re: Best quality brass?? |
|
Donut Slayer wrote: |
Slim, how do you aneal your cases? I've been told to chuck it in a drill and heat the neck with a propane torch until it just starts to turn red. Then quench the case in ice cold water. I do this in a dark room so its easier to see when the brass starts to get red. It makes a nice discoloration just past the shoulder. If you do it too long, the discoloration gets really close to the case head, and that case gets tossed. |
Here ya go DS...put your mind to building this machine mate...
Case Annealing
Personally, I use the warm fingers approach...hold the neck of the case in a propane flame and when the base of case get a bit hot around the fingers it is pretty much right. Ity's slow, but it works well.
_________________ Cheers, Vince
Illegitimi non carborundum
(Never let the bastards grind you down)
Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God.
"Nulla Si Fa Senza Volonta."
(Without Commitment, Nothing Gets Done) |
|
Back to top |
|
|
SingleShotLover Super Member
Joined: Dec 26, 2007 Posts: 1005 Location: Illinois
|
Posted: Tue Jun 24, 2014 4:28 am Post subject: Re: Best quality brass?? |
|
Vince wrote: |
Personally, I use the warm fingers approach...hold the neck of the case in a propane flame and when the base of case get a bit hot around the fingers it is pretty much right. Ity's slow, but it works well. |
Same here. Plus it keep you from over-heating the brass. That can cause damage too. I have also heard of people standing cases in a shallow pan of water, heating the necks with a propane torch and then tipping them over to quench. Haven't tried it, but might be a way to prevent blistered fingers!
_________________ If you can't hit it with one, you probably can't with two either!
The biggest problem with a closed mind is that it never seems to come with a closed mouth.
SSL |
|
Back to top |
|
|
Aloysius Super Member
Joined: Nov 03, 2009 Posts: 2440 Location: B., Belgium
|
Posted: Tue Jun 24, 2014 4:49 am Post subject: Re: Best quality brass?? |
|
SSL, that works OK. I use a small aluminium pan I found in an old fridge (to make ice-cubes). For me it works best when I deprime the cases before annealing, so that the water can enter inside the case. Easier to dry them afterwards also. A tip: don't use the blue innerpart of the propane flame. The flame is the hottest about 1/2" before the blue innerpart + somehow that blue unburned propane likes do perform a chemical reaction with the brass.
|
|
Back to top |
|
|
slimjim Super Member
Joined: May 16, 2009 Posts: 8316 Location: Fort Worth TX
|
Posted: Tue Jun 24, 2014 5:49 am Post subject: Re: Best quality brass?? |
|
Donut Slayer wrote: |
Slim, how do you aneal your cases? |
I do not anneal my brass. I use a Redding S type bushing die so I don't work harden the brass.
_________________ "To anger a conservative, lie to him. To anger a liberal, tell him the truth." - Theodore Roosevelt
"The world is a dangerous place to live; not because of the people who are evil, but because of the people who don't do anything about it." - Albert Einstein |
|
Back to top |
|
|
lesterg3 Super Member
Joined: Nov 30, 2008 Posts: 1328 Location: Dixie
|
Posted: Tue Jun 24, 2014 10:34 am Post subject: Re: Best quality brass?? |
|
_________________ "A democracy is nothing more than mob rule, where fifty-one percent of the people may take away the rights of the other forty-nine. "--Thomas Jefferson
The strongest reason for the people to retain the right to keep and bear arms is, as a last resort, to protect themselves against tyranny in government. -- Thomas Jefferson
"Americans have the right and advantage of being armed - unlike the citizens of other countries whose governments are afraid to trust the people with arms."--James Madison
"The tree of liberty must be refreshed from time to time with the blood of patriots and tyrants." Thomas Jefferson.
NRA Life Member
Vietnam War Vet 68-69 |
|
Back to top |
|
|
lesterg3 Super Member
Joined: Nov 30, 2008 Posts: 1328 Location: Dixie
|
Posted: Tue Jun 24, 2014 1:24 pm Post subject: Re: Best quality brass?? |
|
Sorry, was in a big hurry, well not me but the other more important half. But, I saw and read the above site and found it very interesting. Not that the automated systems were not cool, But, I like simplicity. I have some more questions and comments about alignment of projectile to cartridge, and especially about the squareness and perpendicularity of the bolt face to the center-line of the bore, but don't have the time today.
_________________ "A democracy is nothing more than mob rule, where fifty-one percent of the people may take away the rights of the other forty-nine. "--Thomas Jefferson
The strongest reason for the people to retain the right to keep and bear arms is, as a last resort, to protect themselves against tyranny in government. -- Thomas Jefferson
"Americans have the right and advantage of being armed - unlike the citizens of other countries whose governments are afraid to trust the people with arms."--James Madison
"The tree of liberty must be refreshed from time to time with the blood of patriots and tyrants." Thomas Jefferson.
NRA Life Member
Vietnam War Vet 68-69 |
|
Back to top |
|
|
Vince Site Admin
Joined: May 25, 2005 Posts: 15721 Location: Brisbane AUSTRALIA
|
|
Back to top |
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|