|
45-70 Siamese Mauser, one of two I have built in the last 12 months or so.-320 viewsTimney trigger, Lothar Walther ported barrel and a custom English Walnut stock with cherry tip and cap. Scope is a Nikon.
|
458 Lott Custom-308 viewsCustom rifle on Montana Rifle Co 1999 Action with MRC 26 inch 1-14 twist barrel, New England Custom Gun Express sights, exhibition grade Bastogne Walnut stock, Madagascar Ebony tip, cap and cross bolt plugs, Limbsaver pad. Stock is double cross bolted and has a 7 inch, 3/8 diameter steel rod epoxied into the wrist. Steel is rust blued. The stock is from one of my blanks.
|
Remington 510 P Restored-193 viewsThis is a 510 P that I restored. The P indicates a peep sight.
|
Restored 511 Remington-323 viewsThe 510, 511, 512 and 513 Remingtons were some of the finest sporting 22 rifles ever made. I buy and restore 500 Series Remington 22 rifles. This is one of my restored guns.
|
My First Rifle-254 viewsThis 512 was given to me on my 9th birthday. The scope rails were cut by Dick Riley of Hookset, NH who would later become the president of the NRA. I worked part time in Dick's shop when I was in high school.
|
Remington 512 Restored-204 viewsThis is a 512 that I restored.
|
Remington 513 T Restored-185 viewsThis is a 513 T that I restored. The gun was a basket case, painted, pitted, etc. It had seem many years service in a NJ high school rifle team before I found it in a pawnshop in Florida. I do kave the open sights for it, including the rear peep and the Lyman globe front with all of the inserts.
|
6x47 Custom XP-100-225 viewsThis was a basket case, rusted, painted, badly fouled, etc. I took it apart, turned the barrel, recut the chamber, recut the crown, stripped the wood and totaly refinished the inside and outside. The 6x47 shot sub .25 inch groups at 50 meters when done.
|
260 XP100 Custom-382 viewsThis is a 260 that I built on an old XP action. The stock is zebra wood with a walnut tip and cap. The Duglas 1-9 twist barrel is fluted and has a muzzle break. The trigger is a Taylor with a 4 oz pull weight. The bolt is fluted and the bolt shroud has been turned to reduce the weight. The scope is a Weaver V-8. The gun will do right a 3,000 fps with a 100 gr Sierra, but is very accurate with the 120 MK.
|
6.5x55 Swede w/ Misquete Stock Left side-205 viewsThis is the latest addition to the tribe. It is a highly modified Swedish Mauser. In addition to my normal modifications as outlined in my article, this action has been made smaller by reducing the magazine height by one round, then the sides of the stock and buttstock have been thinned to create a sevite little 4 shot rifle. The barrel is original with the steps removed and cut to 20 inches. The stock is screwbean misquete with an Enlish walnut tip. The rifle shoots sub .5 inch groups with the Hornady 140.
|
Model 96 Swede Right Side of Action Close-187 viewsThese are the modifications to the bolt as mentioned. Note the removal of the cocking knob at the rear of the bolt, the new scope safety, flat bolt handle, shaped knob and the angle that the bolt is swept back. The Timney trigger has been shortened and the tip rounded. In the photo you can also see that the rounded ridge behind the stripper clip opeaning has been removed. The bolt body has been polished to 500 grit and jewled or engine turned. The extractor has been blued but should be left polished as it will scratch when the bolt is worked.
|
XP-100 in 6.5 BR-435 viewsThis is a 6.5 BR that I built. The action has been altered, a spoon bolt handle added. The barrel is a Sheilen ultra match SS 1-8 twist. Stock is walnut with maple tip and cap. Trigger is a Taylor 4 oz. Scope mount is custom, extended mount. Scope is a 3x12 Burris Signature. The gun was built to shoot 1/2 size targets and 500 meter silhouette.
|
59 pictures on 5 page(s) |
|
|
2 | |
|
|
|