Login or Register
HomeCommunity ForumsPhoto AlbumsRegister

User Info

Welcome Anonymous

Latest: scottfh
New Today: 0
New Yesterday: 0
Overall: 12686

People Online:
Members: 0
Visitors: 110
BOT: 2
Total: 112
Who Is Where:
01: Forums
02: Forums
03: Forums
04: News
05: Forums
06: Forums
07: Forums
08: Forums
09: Forums
10: Forums
11: Forums
12: Forums
13: Forums
14: Home
15: Forums
16: Forums
17: PointBlank Ballistics
18: Home
19: Forums
20: Forums
21: Forums
22: Forums
23: Photo Albums
24: Forums
25: Forums
26: Forums
27: News
28: Forums
29: Your Account
30: Forums
31: Forums
32: Statistics
33: Forums
34: Forums
35: Forums
36: Photo Albums
37: Home
38: Home
39: Forums
40: Forums
41: Forums
42: Home
43: Forums
44: Forums
45: Forums
46: Forums
47: Forums
48: Forums
49: Forums
50: Forums
51: Forums
52: Forums
53: Forums
54: Forums
55: Forums
56: Forums
57: Forums
58: Home
59: Home
60: Forums
61: Forums
62: Forums
63: Forums
64: Photo Albums
65: Forums
66: Forums
67: Forums
68: Forums
69: Forums
70: Forums
71: Forums
72: Forums
73: Home
74: Forums
75: Forums
76: Photo Albums
77: Home
78: Forums
79: Forums
80: Forums
81: Forums
82: Forums
83: Photo Albums
84: Photo Albums
85: Forums
86: Forums
87: Forums
88: Your Account
89: Forums
90: Photo Albums
91: Forums
92: Forums
93: Forums
94: Home
95: Forums
96: Forums
97: Forums
98: Forums
99: Forums
100: Forums
101: Forums
102: Forums
103: Forums
104: Forums
105: Forums
106: Home
107: Articles: Topics
108: Home
109: Forums
110: Forums
01: Forums
02: Forums

Staff Online:

No staff members are online!

Coppermine Stats
Photo Albums
 Albums: 305
 Pictures: 2367
  · Views: 525763
  · Votes: 1312
  · Comments: 86

Support our Advertisers

  Ruger #1 Accuracy

ShootingRuger #1 Accuracy
by Ed Harmon

First a notification: Ruger takes the position that any modification to their guns voids their warranty. They also consider hand loads a no-no. If you return a gun for work that has been modified they may just return it without work being performed and charge you shipping, so be aware and consider the potential consequences before you modify your Ruger firearm.


The #1 and the #3 Rifles, upon examination, are obviously designed to have the forearm separated from the barrel otherwise the forearm would be screwed to the barrel, like a Martini or Martini Cadet. The two actions are the same without the levers and both will take the same barrels. Why are the barrels not free floated from contact with the wood of the forearm at the factory? Forget the hype, it is purely economic. To get the correct clearance under the barrel and along each side of the barrel, takes time and time is money in manufacturing.

Ok, we start by removing the forearm from the rifle. You can, if you wish, try the O ring trick by buying a couple of O rings at the hardware store to fit the shank of the forend screw. Before any modification, put one O ring at a time between the hangar and the wood. This sometimes will work. Otherwise we continue.

If you are familiar with glass bedding a rifle to start with, you relieve the wood to provide an even line down both sides of the barrel; a barrel channel rasp helps to make this job quick and easy. If you have not done a glass bed for a barrel channel before, put the forearm back in place, run a pencil down the wood, alongside the barrel and cut the wood back to the pencil line using a barrel channel rasp. Go slow; it is difficult to stick wood back on. Use a fine cut flat wood rasp or a course flat steel file to straighten the lines if needed. Then use a sanding block to finish. You will need one layer of Duct Tape on each side for clearance. Stick a layer of duct tape on the barrel lengthwise and when the forearm fits back on the barrel just a bit snugly, you are about right.

Once you get the sides cut you can start on the bottom, where the hanger makes contact. With an oil burner, soot up the hangar and barrel, pressing the forearm into place. With the barrel channel rasp remove all marks in the barrel channel. Then go back to the hanger contact area and with a motor tool and small carbide router bit, remove the marks or the contact points made by the hanger. You only need to rough up three points because the will need to be extended or built up in any case.

In the attached photos an arrow points to the three places that require glass. All you need do is rough the surface of the wood so the glass will stick, without peeling or flaking off. Put two layers of duct tape only along the bottom of the barrel then coat the metal and the tape with Johnson

Posted by SwampFox on Thursday, August 27, 2009 (17:45:38) (5162 reads) [ Administration ]
Related Links
 More about Shooting

Most read story about Shooting:

Article Rating
Average Score: 4.66
Votes: 3

Please take a second and vote for this article:

Very Good



Valid CSS! Valid HTML 4.01!
Click to check if this page is realy HTML 4.01 compliant for speed :)

All logos and trademarks in this site are property of
The comments are property of their posters, all the rest © 2011 by
Interactive software released under GNU GPL, Code Credits, Privacy Policy

.: Upgraded to DragonFly 9.2 by Dizfunkshunal :.