View previous topic :: View next topic |
Author |
Message |
chambered221 Super Member
Joined: Aug 17, 2007 Posts: 3455 Location: Lost for good !!!
|
Posted: Mon Jan 14, 2008 12:44 pm Post subject: Annealing cases |
|
Does anyone anneal their brass?
If so, why?
Looking for how to info on the subject.
I see annealing kits avalible, are they needed?
Some general discussion please!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|
|
Back to top |
|
|
Pumpkinslinger Super Member
Joined: Sep 22, 2007 Posts: 5002 Location: NC foothills
|
Posted: Mon Jan 14, 2008 2:47 pm Post subject: Re: Annealing cases |
|
I have never annealed brass cases but my understanding is that it is done because of “work hardening” the case. Either in reforming the case from one cartridge to another or in reloading the same case many times the repeated expanding/resizing of the brass changes the grain structure, making it get hard. Annealing the brass by heating it and letting it air cool softens it. I’ve seen articles about this where they placed cases in a shallow pan of water, to protect the base, and heated just the mouth/neck/shoulder area with a torch.
All that said, the only times I could see going to all that trouble would be:
1 – When converting one case into another where it requires several passes through the dies.
2 – When resizing a case that is pretty rare or hard to find.
So far everything I load is pretty common so I haven’t had to try this. Now if Hitlery gets elected I might have to start annealing 9mm, .357 Mag, …
_________________ Mike
"I ain't no better than anybody else, and there ain't nobody better than me!" Ma Kettle |
|
Back to top |
|
|
204Shooter Member
Joined: Jan 28, 2007 Posts: 68 Location: Diana, TX
|
Posted: Mon Jan 14, 2008 5:25 pm Post subject: Re: Annealing cases |
|
Pumpkinslinger, it is better to heat the brass neck to a very dim red and then quench the heat by dunking it into cold water. If you let it cool down slowly in air, you don't get much softening of the brass. If you work your brass hard (as in hot loads), you may need to anneal it every 5-6 reloads to keep the neck from spliting.
204
_________________ Life is a series of choices. It is how we manage those choices that counts. |
|
Back to top |
|
|
gelandangan Super Member
Joined: May 07, 2006 Posts: 6398 Location: Sydney Australia
|
Posted: Mon Jan 14, 2008 6:11 pm Post subject: Re: Annealing cases |
|
Brass need to be cooled QUICKLY for it to retain large crystal structure. Cooling it slowly in room temperature will somewhat harden it rather than anneal it.
usually you put the cases inside a tray with water up to the neck of the cases or to the lowest part you want it to anneal. Then you torch the case till glowing reddish and quickly tip the case over into the water to retain its annealed form.
I shoot over 200 to 400 rounds of 38/357 almost every week in the range, my cases has been reloaded for I think over 50 times since before the turn of the millennium and I have annealed it multiple times (once every blue moon - takes over 4 hours to do the lot 1000+ cases). I still lost a case or two every month or so. I reckon if I didnt anneal it, I may have to buy a new set of cases long before.
Then again since I load the cartridge really softly, 3.2gn AS30 on 135gn BNWC lead, there is almost no case stretching at all. there is only the matter of belling the case mouth when reloading that chance of damages exist.
_________________ A straight line is the shortest distance between two points.
A smile is the shortest distance between two people.
Do - Not try!
gelandangan.weebly.com/ |
|
Back to top |
|
|
Pumpkinslinger Super Member
Joined: Sep 22, 2007 Posts: 5002 Location: NC foothills
|
Posted: Tue Jan 15, 2008 12:14 am Post subject: Re: Annealing cases |
|
From my reading on other metallurgy I understood that annealing involved slow cooling. Anyway, I found this article online…
Here we go >> www.6mmbr.com/annealing.html
_________________ Mike
"I ain't no better than anybody else, and there ain't nobody better than me!" Ma Kettle |
|
Back to top |
|
|
BHP9 Rookie Member
Joined: Dec 28, 2007 Posts: 4 Location: Ontario, Canada
|
Posted: Tue Jan 15, 2008 6:45 am Post subject: Re: Annealing cases |
|
Annealing isn't necessary unles you have some obscure brass or fireformed into something like an AI caliber.
_________________ Proud member of WTFDTSG club.
Stercus Accidit = Shit Happens in Latin. |
|
Back to top |
|
|
SingleShotLover Super Member
Joined: Dec 26, 2007 Posts: 1005 Location: Illinois
|
Posted: Tue Jan 15, 2008 7:08 am Post subject: Re: Annealing cases |
|
Two points: Brass is annealed by quenching quickly in water as mentioned. Brass used with blackpowder in cartridges should definitely be annealed to allow it to properly seal the chamber upon ignition.
The annealing process varies according to the metal and composition. Certain steels anneal like brass (with quick quenching) others anneal by cooling at room temperature.
Honestly, I guess I'm just too lazy to mess with it. I just throw brass away when it gets work-hardened, but I certainly can see the benefits if you are either forming cases from another cartridge or trying to make exotic cases last as long as possible.
_________________ If you can't hit it with one, you probably can't with two either!
The biggest problem with a closed mind is that it never seems to come with a closed mouth.
SSL |
|
Back to top |
|
|
SwampFox Super Member
Joined: Jul 15, 2005 Posts: 1040 Location: Destin, Florida
|
Posted: Tue Jan 15, 2008 9:30 am Post subject: Re: Annealing cases |
|
Chambered221,
I anneal most of my bottleneck brass as I shoot mostly wildcats or cartridges I make from other factory offerings.
The process is very simple, get yourself a propane torch a flat bottom pan that will allow water to come up half way on the cartridges. Place the water in the pan and set empty cartridges upright in the water. This should be done in a darkened room. With the propane torch heat the neck and shoulder of each cartridge until it just starts to turn redish brown, tip the case over with the torch tip into the water. Do not heat till glowing red as the brass will slump and be destroyed. The redish brown change can not be seen in a brite light.
When finished, empty the water, dry the brass in a folded towel, allow to air dry for a day or two and drop the brass in a tumbler. It will polish back to brite, even nickel brass. You are now ready to form.
Ed
_________________ The inherent vice of capitalism is the unequal sharing of the blessings. The inherent blessing of socialism is the equal sharing of misery.
-Winston Churchill |
|
Back to top |
|
|
Bushmaster Super Member
Joined: Jun 12, 2005 Posts: 11393 Location: Ava, Missouri
|
Posted: Tue Jan 15, 2008 9:45 am Post subject: Re: Annealing cases |
|
I'm usually looking at case head seperation before I need to anneal them...After about 6 to 8 reloadings or 4 to 5 trimmings I just toss them...They're the second cheapest component of reloading.
_________________ I have one nerve left and yer standin' on it...
DEMOCRACY Two wolves and one sheep voting on what to have for lunch...
LIBERTY A well armed sheep contesting the outcome of the vote... |
|
Back to top |
|
|
skb2706 Member
Joined: Apr 10, 2006 Posts: 269
|
Posted: Tue Jan 15, 2008 10:06 am Post subject: Re: Annealing cases |
|
I just annealed 250 pieces last night. Once fired Winchester 22-250 brass. When I was sizing these I had four cases neck split so I knew the only way to salvage it was to anneal. Typically this means the brass was not annealed correctly when it was made.
I anneal my wildcat stuff that requires serious neck downs as well.
I use the propane torch, shallow pan of water technique. Heat til it just shows a hint of red. Not very scientific but it has worked for 30 plus years.
|
|
Back to top |
|
|
A17Shooter Super Member
Joined: Jan 26, 2005 Posts: 322 Location: California Foothills (Gold Country)
|
Posted: Tue Jan 15, 2008 12:55 pm Post subject: Re: Annealing cases |
|
When heating the cases for annealing, I hold them between thumb and forefinger. I use a small propane torch that has about a 1/4" nozzle to heat the neck. When the cases get uncomfortably hot I drop them onto a towel.
_________________ _________________
A17Shooter |
|
Back to top |
|
|
gelandangan Super Member
Joined: May 07, 2006 Posts: 6398 Location: Sydney Australia
|
Posted: Tue Jan 15, 2008 4:50 pm Post subject: Re: Annealing cases |
|
Here is a link to a quite interesting annealing article
www.6mmbr.com/annealing.html
_________________ A straight line is the shortest distance between two points.
A smile is the shortest distance between two people.
Do - Not try!
gelandangan.weebly.com/ |
|
Back to top |
|
|
sniper Super Member
Joined: Aug 18, 2005 Posts: 735 Location: Utah
|
Posted: Thu Jan 17, 2008 12:00 pm Post subject: Re: Annealing cases |
|
The propane torch method is way too complicated, per John Barnsness, who did an article in Handloader or Rifle Magazine some months ago.
Seems like John has a friend, who is a metallurgist and a shooter. He figured out, using tempilaq, that a normal household candle provides enough heat to anneal brass. He holds the case about in the middle of the body, and keeps turning it in the flame till it gets too hot to comfortably hold, then drops it on a wet towel.
Barnsness says it works. Cheap and simple, but where's the fun in that?
|
|
Back to top |
|
|
Bushmaster Super Member
Joined: Jun 12, 2005 Posts: 11393 Location: Ava, Missouri
|
Posted: Thu Jan 17, 2008 12:40 pm Post subject: Re: Annealing cases |
|
Tin of water, a propane torch and a pair of pliers...We're in business. Be damned if I'm going to hold that brass with my bare fingers...I know how fast brass transfers heat...
Someone told me that all you had to do was to stand them upright in a pan of water and heat the necks with a propane torch until they were almost red then tip them over into the water...Forgot who it was...(CRS)
_________________ I have one nerve left and yer standin' on it...
DEMOCRACY Two wolves and one sheep voting on what to have for lunch...
LIBERTY A well armed sheep contesting the outcome of the vote... |
|
Back to top |
|
|
hunterjoe21 Super Member
Joined: Mar 30, 2007 Posts: 1486 Location: Miles City, Montana
|
Posted: Thu Jan 17, 2008 8:14 pm Post subject: Re: Annealing cases |
|
As copied from another forum:
"The goal here is to restore pliability to the brass, yet not soften it too much so as to create inadequate neck tension on the bullet, or to damage the structure of the brass. The correct temperature is near 660 degrees Fahrenheit, but no hotter. Heating the brass to a glowing red color is way too hot and will damage it, so that is to be avoided.
The temperature you need will generate an "light blue" color, evenly in the neck that does not extend past the bottom of the shoulder. This color is more easily discerned in low light. The primary reason I see for setting cases in the water, is to be absolutely sure that the softening effect does not extend to the case head...that part of the case has to stay hard. But if your method allows that much heat to migrate to the head of the case, you are doing something wrong anyway. "
and then a two posts later:
"You can get a heat crayon at any welding supply that melts at 650 degrees. You could mark around the neck heat it till it melts and you would be very close to 660.They cost around 10 bucks and would do several hundred rounds."
This is only what I've read about annealing cases. I tend to agree with Bushmaster, after 4-5 loadings I toss 'em and start over with new. Winchester brass is NOT that expensive. I might feel differently If I purchased Lapua, Norma, or even Nosler Custom brass.
_________________ My 1911 is more effective than your 911. |
|
Back to top |
|
|
|